banner image
Description

The Ace #12 SKINNYnSTRONG™ Roofing Screws are designed to be used with Ace 3” Insulation Plates to secure ridged insulation, cover boards and base sheet, to steel (18* to 22Ga) or certain wood structural decks. Fasteners ranging in length from 1-5/8” to 8” are available to meet a variety of commercial roofing applications.

Method of Application
  • Using the #3 Phillips tip provided, and a variable speed drill, engage the fastener into the deck as noted below. Do not over or under drive the fastener. Threads must engage the decking material per Technical Specifications.
  • Determine screw length as follows:
    • Steel Decks: Select fastener length to penetrate through the deck a minimum of 3 ⁄ 4" (19.1 mm).
    • Wood Decks: Select fastener length to penetrate into or through the deck a minimum of 1" (25.4 mm).
  • Ace #12 Fasteners may not work as expected through existing roof systems or unusual substrates.
  • For best results, use a variable-speed screw gun (0-2500* RPM). Do not over tighten.
Storage

Store in original, unopened packaging protected from the weather.

Precautions

Eye protection must be worn during the installation of the fasteners.


FBC: FL41667


Ace Screws’ products and specifications are subject to change without notice.

Neither Ace Screws nor its representatives practice architecture/engineering. Ace Screws offers no opinion on and expressly disclaims any responsibility for the soundness of any structure. Ace Screws accepts no liability for structural failure or resultant damages. Consult a competent structural engineer prior to installation if the structural soundness or structural ability to properly support a planned installation is in question. No Ace Screws representative is authorized to vary this disclaimer.

*When installing into 18Ga deck, use a slow, controlled approach and feather the trigger to avoid binding or bit slippage; excessive speed can cause damage to the fastener.

Product Packaging
Screw LengthThread LengthPieces per Paillbs. Per PackagePackages per Pallet
1-5/8” (41.3 mm)Full1,00012 lbs60
2” (50.8 mm)Full1,00015 lbs60
2-1/4” (57.2 mm)Full1,00017 lbs60
2-7/8” (73.0 mm)Full1,00021 lbs60
3” (76.2 mm)Full1,00023 lbs60
3-1/4” (82.5 mm)3” (76.2 mm)1,00023 lbs60
3-3/4” (95.3 mm)3” (76.2 mm)1,00026 lbs60
4” (101.6 mm)3” (101.6 mm)1,00029 lbs60
4-1/2” (114.3 mm)4” (101.6 mm)1,00031 lbs40
5” (127.0 mm)4” (101.6 mm)1,00036 lbs40
6” (152.4 mm)4” (101.6 mm)1,00041 lbs40
7” (177.8 mm)4” (101.6 mm)1,00048 lbs40
8” (203.2 mm)4” (101.6 mm)1,00054 lbs40
Properties
PropertyTypical Performance
MaterialManufactured using SAE 1022 HEAT TREATED STEEL
Threads / Inch13
Fastener TipHigh Performance Drill Point
Fastener Head#3 Phillips Drive

Typical properties and characteristics are based on samples tested and are not guaranteed for all samples of this product. This data and information are intended as a guide and does not reflect the specification range for any particular property of this product.

Ace #12 Fastener Minimum Specification (Actual Test Results)
3rd Party Independent: (Nemo ETC | SGS SA | Element Materials Technology)Pull Out Test Results
ASTM F6096/F606M-2019MinimumAverageGa, ksiAverage
Tensile2760 lbf2980 lbf22 Ga, 40 Grade461 lb
Shear Test (Single)1483 lbf1560 lbf22 Ga, 80 Grade483 lb
Torque Test98 in-lbs99 in-lbs19/32” Plywood596 lb
DIN 50018 15 cycles KesternichSpecification
Average


Black e-coat<15 % red rust<5% red rust (Exceeds FM 4470 Requirements)

#12 Roofing Fastener™



#14 Heavy Duty Roofing Fastener